Only allow trained technicians to perform maintenance on this product. For additional information contact factory or nearest Ingersoll Rand Ingersoll Rand Distributor. For additional supporting documentation refer to Table 1 ‘Product Information Manuals’ on page 2. Manuals can be downloaded from ingersollrandproducts.com The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased performance and increased maintenance and will invalidate all warranties.
Table 2: Specifications Air System Rated Performance (at rated pressure/volume) Consumption Net Weight ** Full Drum Full Drum Mid Drum Max Stall Pull, Maximum Model Operating (at rated Rated Force Line Pull Line Speed Line Speed 1st Layer Freeboard Mode pressure and Operating Limit...
6. Do not weld to any part of winch. Refer to Dwg. MHP2686 on page 11, A. Anchor; B. Wire Rope. Refer to Dwg. MHP0133 on page 11, A. Drum. 1. Cut wire rope to length in accordance with wire rope manufacturer’s instructions.
Page 6
Install a 3-way ball valve at the air inlet to the winch. One inlet to the 3-way ball valve Pre-set limit switch settings prevent winch wire rope payout and haul-in by stopping is to be connected to the Main Air Supply. The other inlet is available to be connected air flow to the winch motor when a defined set point has been reached.
OPERATION It is recommended that the user and owner check all appropriate and applicable regulations before placing this product into use. Refer to Product Safety Information n Emergency Stop and Overload System Manual before operating product. The four most important aspects of product operation are: Emergency stop and overload system are standard on MR-CE winches.
Precautions n Winch Brakes 1. Emergency lowering operations must be performed by a minimum of two Manual Drum Band Brake (Standard) personnel trained in the operation of the winch. 2. Communication must be established between lifted person and winch operators. Operators should be able to visually monitor lifted person until The manual drum band brake is applied by pushing down on handle and released landed.
INSPECTION Inspection information is based in part on American Society of Mechanical Engineers 7. Winch Operation. Power winch in both directions. Winch must operate Safety Codes (ASME B30.7). smoothly without sticking, binding or abnormal noises and have minimal vibration. WARNING NOTICE •...
The reduction gear is filled to the correct levels prior to shipment from the factory. WARNING Check oil level before initial winch operation. This component is splash lubricated by oil in the housing and has no other means of lubrication. It is therefore important •...
Page 11
PRODUCT INFORMATION GRAPHICS Air Out Regulator DRUM Air In Lubricator (Dwg. MHP0133) Filter (Dwg. MHP0191) (Dwg. MHP2688) Man Rider (Dwg. MHP2686) View: Facing Air Motor Clockwise Counterclockwise Direction: Direction: Wire Rope Wire Rope Payout Haul-In No Man Rider 1-1/4 inch 90°...
Page 12
PRODUCT INFORMATION GRAPHICS (CONTINUED) Twist Red Button to Reset (Dwg. MHP2558) (Dwg. MHP2398) Push In Turn in a counterclockwise direction to reset Emergency Stop. (Dwg. MHP1348) “Emergency Stop” Button “ON” Button (Dwg. MHP2557) Function Levers Pendant Handle (Dwg. MHP1892) Form MHD56437 Edition 7...
Page 13
Fill Plug Level Plug Drain Plug (Dwg. MHP0222) Form MHD56437 Edition 7...
Page 14
PRODUCT INFORMATION GRAPHICS (CONTINUED) Main Air Supply Fill Plug Drum Position Reduction Gear Rotate handle Assembly to use in normal condition Level Plug Position Emergency Lowering Inlet Inboard Upright (Dwg. MHP3143) (Dwg. MHP0140) Form MHD56437 Edition 7...
Page 15
DECLARATION OF CONFORMITY (CS) PROHLÁŠENÍ O SHODĚ (DA) OVERENSSTEMMELSESERKLÆRING (DE) KONFORMITÄTSERKLÄRUNG (EL) ∆ΗΛΩΣΗ ΑΝΑΓΝΩΡΙΣΗΣ (ES) DECLARACIÓN DE CONFORMIDAD (FI) VAKUUTUS NORMIEN TÄYTTÄMISESTÄ (FR) CERTIFICAT DE CONFORMITÉ (HU) MEGFELELŐSÉGI NYILATKOZAT (IT) DICHIARAZIONE DI CONFORMITÀ (LT) ATITIKTIES DEKLARACIJA (LV) ATBILSTĪBAS DEKLARĀCIJA (NL) SCHRIFTELIJKE VERKLARING VAN CONFORMITEIT (NO) KONFORMITETSERKLÆRING (PT) DECLARAÇÃO DE CONFORMIDADE (PL) DEKLARACJA ZGODNOŚCI (SK) PREHLÁSENIE O ZHODE (SL) IZJAVA O SKLADNOSTI (SV) FÖRSÄKRAN OM ÖVERENSSTÄMMELSE Company: Ingersoll Rand...
Need help?
Do you have a question about the Force 5 Infinity Series and is the answer not in the manual?
Questions and answers