SENDERO INDUSTRIES
Sendero Industries is a full-service civil contractor specializing in site preparation, earthwork, drainage and utilities for private and public projects throughout Texas. They have a 20-year history of successful projects for leading developers, civil engineers and general contractors. They known for our reliability, our understanding of what makes a successful project and our commitment to total satisfaction.
SENDERO INDUSTRIES
Industry:
Civil Engineering Construction Customer Service Project Management
Founded:
2002-01-01
Address:
Houston, Texas, United States
Country:
United States
Website Url:
http://www.senderoindustries.com
Total Employee:
101+
Status:
Active
Contact:
+1 713 868 6960
Email Addresses:
[email protected]
Technology used in webpage:
Microsoft Exchange Online
Official Site Inspections
http://www.senderoindustries.com
- Host name: vps39820.inmotionhosting.com
- IP address: 199.250.200.213
- Location: Los Angeles United States
- Latitude: 33.956
- Longitude: -118.3887
- Metro Code: 803
- Timezone: America/Los_Angeles
- Postal: 90045
More informations about "Sendero Industries"
TI Launchpad MSP430 on Serial in Linux - Electrical Engineering …
The MSP-EXP430G2 LaunchPad Experimenter Board User's Guide (Rev. C) in chapter 3.2 states: The LaunchPad includes a pre-programmed MSP430G2553 device [...] Press button …See details»
Difference between Hz and bps - Electrical Engineering Stack …
Jan 27, 2013 Does Hz and bps mean same? Can a signal be transferred at rate of say Mbps on a channel bandwidth of few Khz?See details»
microcontroller - How to flash MSP430G2211 MCU? - Electrical ...
Jan 24, 2022 It seems like your launchpad's EZ-FET is broken. It is not stable, and by some reason, it becomes broken easily. Try to reset the firmware of EZ-FET by running, $ …See details»
Baud rate vs. Bit rate - Electrical Engineering Stack Exchange
When we initialize a serial communication, we usually have to set the baud rate (e.g. 115200). I notice that many people assume that 115200 means 115200 bits per second. However, each …See details»
microcontroller - Tiva C Series LaunchPad and Breadboard
1 I signed up for a class on edX that involves microcontroller programming, and my kit arrived today so I wanted to start experimenting a bit, the only problem is, I have no clue how to …See details»
What standard UART rates are there?
300 bps was the standard for the first widely-used telephone modems in the 1960's. A number of 30 character per second terminals appeared at the same time. Above 300 bps/300 baud, …See details»
Bidirectional voltage and current switch using mosfets
Feb 28, 2021 The publication does advertise at page 2 that "A bidirectional powers witch (BPS)is an active switch which can support bidirectional current flow when it is in the ON condition and …See details»
How to Power On Texas Instruments Tiva launchpad?
I am attempting to power on a Texas Instruments Tiva TM4C123GH6PM with an external power supplied by the VCC pin from a generic ESC. In the board, there is a non-soldered pin named …See details»
LaunchPad development board talking to itself using a CAN bus
Oct 26, 2014 I have one Texas Instruments Tiva-C Series TM4C123GXL LaunchPad and two MCP2551 transceivers. I am trying to send and receive messages via a controller area …See details»
How to read serial data from oscilloscope
I have a microcontroller (PICAXE 20X2) and a pot meter. I programmed the micro so that it sends any change of pot meter to serial port of PC. Obviously it is a 8bit ADC. Now the interesting …See details»